The maintenance of burner accessories has actually been mentioned once before. This time, the editor of Jinzihao mainly introduces the knowledge of burner maintenance in four steps.
1. Disassemble the burner
Drain the oil in the heating oil pool. Remove the power cord, air pipe, upper oil pipe, and oil pump motor power cord. Remove the burner.
Unscrew the screws at the bottom of the filter tank and drain the oil. Unscrew the screws in the middle of the filter tank cover, open the filter tank cover, and take out the filter. The parts of the burner that need to be cleaned and maintained are disassembled.
2. Clean the burner parts
Remove the dirt on the flame stabilizing plate and open the gap. Clean the carbon deposits on the electrode.
Use carburetor cleaning agent to clean the fuel injector, nozzle, oil pipe, and oil suction pipe. If the oil pipe and oil suction pipe wall are fouled, use a cleaning rod to clear them. Check whether the O-ring is intact and replace it if necessary.
Clean the oil stains on the heating wire and temperature sensor. Clean the sludge at the bottom of the heating oil pool.
Clean the filter tank and filter. Drain the oil in the oil tank, clean the bottom sludge, and clean the oil tank.
3. Assembly: Assemble in reverse order according to the disassembly order
When installing the electrode, pay attention to the gap between the electrode (2.5mm) and the gap between the electrode and other parts. (Do not ground) After assembly, add oil to the heated oil pool to the liquid level mark, and then install and use. (The above maintenance work for the burner is performed once a year.)
4. Daily maintenance
Cleaning the flame stabilizing plate (cleaning for 3-15 days according to the cleanliness of the fuel oil and the use rate of the burner)
Cleaning the fuel injector and oil pipe (clean once every three months) Method: Use high-pressure air to blow at the fuel injector to clear the oil path. (Do not use carburetor cleaning agent to clean the fuel injector)
Cleaning the filter, photoreceptor, and oil overflow tank (clean in time according to the use situation)
The maintenance of burner accessories has actually been mentioned once before. This time, the editor of Jinzihao mainly introduces the knowledge of burner maintenance in four steps.
1. Disassemble the burner
Drain the oil in the heating oil pool. Remove the power cord, air pipe, upper oil pipe, and oil pump motor power cord. Remove the burner.
Unscrew the screws at the bottom of the filter tank and drain the oil. Unscrew the screws in the middle of the filter tank cover, open the filter tank cover, and take out the filter. The parts of the burner that need to be cleaned and maintained are disassembled.
2. Clean the burner parts
Remove the dirt on the flame stabilizing plate and open the gap. Clean the carbon deposits on the electrode.
Use carburetor cleaning agent to clean the fuel injector, nozzle, oil pipe, and oil suction pipe. If the oil pipe and oil suction pipe wall are fouled, use a cleaning rod to clear them. Check whether the O-ring is intact and replace it if necessary.
Clean the oil stains on the heating wire and temperature sensor. Clean the sludge at the bottom of the heating oil pool.
Clean the filter tank and filter. Drain the oil in the oil tank, clean the bottom sludge, and clean the oil tank.
3. Assembly: Assemble in reverse order according to the disassembly order
When installing the electrode, pay attention to the gap between the electrode (2.5mm) and the gap between the electrode and other parts. (Do not ground) After assembly, add oil to the heated oil pool to the liquid level mark, and then install and use. (The above maintenance work for the burner is performed once a year.)
4. Daily maintenance
Cleaning the flame stabilizing plate (cleaning for 3-15 days according to the cleanliness of the fuel oil and the use rate of the burner)
Cleaning the fuel injector and oil pipe (clean once every three months) Method: Use high-pressure air to blow at the fuel injector to clear the oil path. (Do not use carburetor cleaning agent to clean the fuel injector)
Cleaning the filter, photoreceptor, and oil overflow tank (clean in time according to the use situation)