The burner is an important component of the gas boiler, mainly used to ignite and burn fuel. It can be said that whether the burner operates normally will directly affect the overall operation effect of the gas boiler. Once the burner of the gas boiler fails to work properly, it will bring serious profit losses to the production and construction of the enterprise. The burner does not operate for the following reasons: 1. The gas pressure is lower than the low-pressure protection switch. Close the cut-off ball valve and check whether the pressure reducing valve or the pressure regulating box is faulty. Observe the boiler water level gauge, grasp the real water level, and manually fill the water to eliminate the fault.
1. After the flame moves due to unstable gas supply, the flame goes out. Processing steps: adjust the gas pressure and restart. 2. The flame detector is broken. The flame detection probe is grounded during operation, or the daily flame cannot be detected when there is dust, causing fire extinguishing. Processing steps: adjust the direction of the detection needle, clean the dust on the surface of the detection needle, and restart. 3. The accessories are broken. The circuit is unstable, resulting in fire extinguishing during operation. Processing steps: call the circuit engineer to check the circuit and connection lines. Why did the fuel steam boiler burner suddenly extinguish when it was burning normally? Gas Boiler | Fuel Boiler | Steam Boiler Environmental Equipment Co., Ltd. 1. After the unstable gas supply caused the fire to swing, extinguish the fire. Solution steps: adjust the pressure load and restart. 2. The fire detector is broken. The fire detection needle is grounded when it is put into use, or the normal fire cannot be detected when there is dust, and the fire cannot be ignited. Solution steps: adjust the position of the detection needle, remove the dirt on the surface of the detection needle, and restart. 3. The component is broken. The circuit is unstable, causing the process to not ignite. Solution steps: Call the distribution worker to repair the circuit and the connection line.
1. Ignition rod. If there is a problem with the ignition rod of the burner, it will directly affect the operation. This situation is mostly because the ignition rod has carbon slag, oil stains, or is cracked, damp, and leaking, resulting in failure to ignite and operate normally. 2. Failure to ignite. The ignition rod seems normal but cannot ignite. This situation may be caused by a variety of reasons, such as poor ventilation or blockage of the cyclone disk, or stains on the nozzle. In addition, the distance between the ignition rod and the nozzle is too close, and the damper design angle is too small. 4. The fire is small. If the gas boiler is normal at a low fire and turns to a high fire, it goes out or flickers unsteadily. These may be that the boiler damper is set too large, and the oil nozzle is worn or dirty.
The burner is an important component of the gas boiler, mainly used to ignite and burn fuel. It can be said that whether the burner operates normally will directly affect the overall operation effect of the gas boiler. Once the burner of the gas boiler fails to work properly, it will bring serious profit losses to the production and construction of the enterprise. The burner does not operate for the following reasons: 1. The gas pressure is lower than the low-pressure protection switch. Close the cut-off ball valve and check whether the pressure reducing valve or the pressure regulating box is faulty. Observe the boiler water level gauge, grasp the real water level, and manually fill the water to eliminate the fault.
1. After the flame moves due to unstable gas supply, the flame goes out. Processing steps: adjust the gas pressure and restart. 2. The flame detector is broken. The flame detection probe is grounded during operation, or the daily flame cannot be detected when there is dust, causing fire extinguishing. Processing steps: adjust the direction of the detection needle, clean the dust on the surface of the detection needle, and restart. 3. The accessories are broken. The circuit is unstable, resulting in fire extinguishing during operation. Processing steps: call the circuit engineer to check the circuit and connection lines. Why did the fuel steam boiler burner suddenly extinguish when it was burning normally? Gas Boiler | Fuel Boiler | Steam Boiler Environmental Equipment Co., Ltd. 1. After the unstable gas supply caused the fire to swing, extinguish the fire. Solution steps: adjust the pressure load and restart. 2. The fire detector is broken. The fire detection needle is grounded when it is put into use, or the normal fire cannot be detected when there is dust, and the fire cannot be ignited. Solution steps: adjust the position of the detection needle, remove the dirt on the surface of the detection needle, and restart. 3. The component is broken. The circuit is unstable, causing the process to not ignite. Solution steps: Call the distribution worker to repair the circuit and the connection line.
1. Ignition rod. If there is a problem with the ignition rod of the burner, it will directly affect the operation. This situation is mostly because the ignition rod has carbon slag, oil stains, or is cracked, damp, and leaking, resulting in failure to ignite and operate normally. 2. Failure to ignite. The ignition rod seems normal but cannot ignite. This situation may be caused by a variety of reasons, such as poor ventilation or blockage of the cyclone disk, or stains on the nozzle. In addition, the distance between the ignition rod and the nozzle is too close, and the damper design angle is too small. 4. The fire is small. If the gas boiler is normal at a low fire and turns to a high fire, it goes out or flickers unsteadily. These may be that the boiler damper is set too large, and the oil nozzle is worn or dirty.