In the burner industry, gas boiler burners and burners account for a relatively large proportion, so these two products are particularly important, especially in the field of equipment technology research and development. Many companies are developing more high-tech and environmentally friendly equipment. But what we need to pay attention to here is that it is also very important to debug and repair during use. Today, let's talk about what we need to pay attention to during the commissioning and maintenance of gas boiler burners and burners.
1. When the gas boiler burner and burner fail to ignite the program continuously, the machine should be stopped for inspection to see whether the gas supply system of the burner is normal and the circuit connection is correct. The burner can be restarted only after the fault is eliminated.
2. It is strictly forbidden to knock or rub the gas supply pipeline with a wrench or metal rod to avoid static electricity or sparks, which may cause gas explosions. It is strictly forbidden to smoke, weld, cut, and other illegal operations at the gas supply valve group or pipeline flange surface. It is strictly forbidden to perform any open flame tests near the pipeline, valve group, and pressure regulating valve to avoid major accidents. To test whether there is fuel in the gas supply pipeline, a gas low-pressure gauge is usually used.
3. In the gas supply pipeline, even if it has been emptied, there are residual gas or droplets on the pipe wall. If there is static sparks and open flames, it will also cause combustion and explosion. When the gas supply pipeline is ventilated and the valve group is faulty, it needs to be disassembled. First, the main valve at the front of the valve group must be cut off, and then the gas in the pipeline from the main valve to the valve group must be vented. Only then can the valve group be disassembled and repaired.
4. In the commissioning of gas boiler burners and burners, gas must be used carefully, safely and efficiently. It is forbidden to use non-explosion-proof electrical tools on site. The VFS504 leak detection device must check the valve group cover before use. It is recommended to use the VS504 leak detection device for burners of 600,000 kcal and above. If the user does not match it, the customer will be responsible for any accidents caused by it.
In the burner industry, gas boiler burners and burners account for a relatively large proportion, so these two products are particularly important, especially in the field of equipment technology research and development. Many companies are developing more high-tech and environmentally friendly equipment. But what we need to pay attention to here is that it is also very important to debug and repair during use. Today, let's talk about what we need to pay attention to during the commissioning and maintenance of gas boiler burners and burners.
1. When the gas boiler burner and burner fail to ignite the program continuously, the machine should be stopped for inspection to see whether the gas supply system of the burner is normal and the circuit connection is correct. The burner can be restarted only after the fault is eliminated.
2. It is strictly forbidden to knock or rub the gas supply pipeline with a wrench or metal rod to avoid static electricity or sparks, which may cause gas explosions. It is strictly forbidden to smoke, weld, cut, and other illegal operations at the gas supply valve group or pipeline flange surface. It is strictly forbidden to perform any open flame tests near the pipeline, valve group, and pressure regulating valve to avoid major accidents. To test whether there is fuel in the gas supply pipeline, a gas low-pressure gauge is usually used.
3. In the gas supply pipeline, even if it has been emptied, there are residual gas or droplets on the pipe wall. If there is static sparks and open flames, it will also cause combustion and explosion. When the gas supply pipeline is ventilated and the valve group is faulty, it needs to be disassembled. First, the main valve at the front of the valve group must be cut off, and then the gas in the pipeline from the main valve to the valve group must be vented. Only then can the valve group be disassembled and repaired.
4. In the commissioning of gas boiler burners and burners, gas must be used carefully, safely and efficiently. It is forbidden to use non-explosion-proof electrical tools on site. The VFS504 leak detection device must check the valve group cover before use. It is recommended to use the VS504 leak detection device for burners of 600,000 kcal and above. If the user does not match it, the customer will be responsible for any accidents caused by it.