As the core equipment of the boiler, the burner directly affects the production efficiency when it fails during operation. Therefore, the emergency treatment measures and methods of daily boiler burner failures must be experienced by boiler operators. What should I do if the gas boiler burner fails? What is the treatment method? Let's learn about it with Zhengguo Boiler.
Introduced the preventive measures of steam boilers and the common faults and treatment methods of steam reciprocating pumps 1. Biomass boilers are a type of boiler. Boilers that use biomass energy as fuel are called biomass boilers. They are divided into biomass steam boilers, biomass hot water boilers, biomass hot air furnaces, biomass thermal oil furnaces, vertical biomass boilers, horizontal biomass boilers, etc. Oil-fired gas boilers refer to boilers that can burn both oil and gas. There was no such dual-fuel boiler before, because the burner was either oil or gas, and there was no dual-fuel burner. With the rapid development of thermal energy equipment in the world, some European countries began to produce and sell oil-fired gas burners. The organic combination of dual-fuel burners and boilers gave birth to a new type of boiler-oil-fired gas boilers. 1. The area close to the steam boiler room should be equipped with sufficient and effective fire-fighting equipment. 2. The steam boiler room must have staff on duty 24 hours a day, take turns to guard, and frequently check the water level line in the boiler to ensure that it is above the safety line to prevent explosions caused by dry combustion. If fire operations are carried out in flammable and explosive places, a fire operation permit must be obtained and adequate fire prevention measures must be taken before firefighting work can be carried out. In the event of a fire, a special person should be on duty at any time to observe the fire situation. 3. It is strictly forbidden to store containers containing flammable gases in the boiler room. 4. The staff of the steam boiler room must be certified before they can take up their posts, and they must be proficient in boiler operation technology and have a certain ability to discover and recognize safety hazards. 5. If boiler safety maintenance is carried out regularly in accordance with the boiler operating procedures, each unsafe standard should be carefully checked during the inspection process. 6. The distribution lines set in the steam boiler room should be protected by metal pipes or non-combustible hard plastic pipes, and the switch boxes should be installed outside the boiler room separately to achieve power outages, and unqualified safety devices are prohibited. 1. What is the reason why the steam reciprocating pump is not draining? How much, how? Answer: (1) Cause of failure: 1 The suction or discharge pipe is blocked. (2) The inlet and outlet valves are stuck. There is air in the cylinder. (4) The suction pipe is not connected tightly. (5) The plunger (piston) seal is seriously damaged. (2) Troubleshooting method: (1) Eliminate pipe blockage. (2) Remove the plugs on the inlet and outlet valves. (3) Fill with water and exhaust the air. (4) Tighten the pipe. (5) Replace the plunger (piston) seal.
Gas boiler burner failure and treatment method - the best gas boiler  1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. 2. The ignition rod is broken. Moisture. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation of the ignition rod is damaged and short-circuited to the ground. 5. Faults in the ignition cable and transformer: the cable is broken, the connector is damaged, causing a short circuit during ignition; the transformer is broken or other faults occur.
What are the common faults and treatment methods of gas boiler burners? , Gas boiler burner faults and treatment methods - the best gas boiler 1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. 2. The ignition rod is broken. Wet. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation sheath of the ignition rod is damaged and short-circuited to the ground. 5. Faults in the ignition cable and transformer: the cable is broken, the connector is damaged, causing a short circuit during ignition; the transformer is broken or other faults occur. There are five treatment measures: clear, replace, adjust the distance, change the line, and change the transformer. 2. The reason why the gas boiler ignition rod has sparks but cannot ignite: 1. The ventilation gap of the cyclone disk is blocked by carbon deposits and the ventilation is poor. 2. The oil nozzle is unclean, blocked or worn. 3. The air door setting angle is too small. 4. The distance between the tip of the ignition rod and the front edge of the oil nozzle is inappropriate (too protruding or retracted) 5. The first oil gun solenoid valve is blocked by debris (small fire oil gun). 6. The oil is too viscous and difficult to flow or the filter system is blocked or the oil valve is not open, so that the oil pump does not absorb enough oil and the oil pressure is low. 7. The filter of the oil pump itself is blocked. 8. The oil contains a lot of water (boiling noise in the heater). The treatment measures are: clear; clean first, if it doesn’t work, replace it with a new one; adjust the distance (3~4mm is better); remove and clean (clean the parts with diesel); check the pipeline and oil filter, insulation equipment; remove the outer screws of the oil pump, carefully remove the outer cover and take out the oil net inside, soak it with diesel; try it with new oil.
Gas boiler burner failure and treatment method-the best gas boiler 1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. What are the common failures and treatment methods of gas boiler burners? . 2. The ignition rod is broken. Damp. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation outer skin of the ignition rod is damaged, short-circuited to the ground. 5. Faults in the ignition cable and transformer: cable breakage, connector damage, short circuit during ignition; transformer breakage or other faults. There are five treatment measures: cleaning, replacement, distance adjustment, line change, transformer change. 2. The reason why the gas boiler ignition rod has sparks but cannot ignite: 1. The ventilation gap of the cyclone disk is blocked by carbon deposits and poor ventilation. 2. The oil nozzle is unclean, blocked or worn. 3. The air door setting angle is too small. 4. The distance between the tip of the ignition rod and the front edge of the oil nozzle is inappropriate (too protruding or retracted) 5. The first oil gun solenoid valve is blocked by debris (small fire oil gun). 6. The oil is too viscous and difficult to flow or the filtration system is blocked or the oil valve is not opened, so that the oil pump does not absorb enough oil and the oil pressure is low. 7. The filter of the oil pump itself is blocked. 8. The oil contains more water (boiling noise in the heater). The treatment measures are: clear; clean first, if it doesn't work, replace with a new one; adjust the oil for testing; adjust the distance (3~4mm is better); remove and clean (clean the parts with diesel); check the pipeline and oil filter, insulation equipment; remove the screws outside the oil pump, carefully remove the outer cover and take out the oil net inside, soak it with diesel; try with new oil. 3. When the gas boiler is normal at a low fire and turns to a high fire, it goes out or flickers unsteadily. Reasons: 1. The air volume of the damper of the high fire is set too large. 2. The micro switch of the oil valve of the high fire (the outermost group of the damper) is not set properly (the setting is larger than the air volume of the damper of the high fire). 3. The viscosity of the oil is too high and it is not easy to atomize (heavy oil). 4. The distance between the cyclone disk and the oil nozzle is improper. 5. The oil nozzle of the high fire is worn or dirty. 6. The heating temperature of the reserve oil tank is too high, causing the steam to make the oil pump deliver oil smoothly. 7. The oil in the oil boiler contains water. Treatment measures: gradually reduce the test; increase the heating temperature; adjust the distance (between 0~10mm); clean or replace; set it to about 50℃; change the oil or drain. 4. Reasons for the increase in noise of the gas boiler burner: 1. The stop valve in the oil circuit is closed or the oil inlet is insufficient, and the oil filter is blocked. 2. The oil inlet temperature is low, the viscosity is too high or the pump oil inlet temperature is too high. 3. The oil pump is faulty. 4. The fan motor bearing is damaged. 5. The fan impeller is too dirty. Treatment method: ① Check whether the valve in the oil pipeline is open, whether the oil filter is working properly, and clean the filter of the pump itself. ② Heat the oil or lower the oil temperature. ③ Replace the oil pump. ④ Replace the motor or bearing. ⑤ Clean the fan impeller.
As the core equipment of the boiler, the burner directly affects the production efficiency when it fails during operation. Therefore, the emergency treatment measures and methods of daily boiler burner failures must be experienced by boiler operators. What should I do if the gas boiler burner fails? What is the treatment method? Let's learn about it with Zhengguo Boiler.
Introduced the preventive measures of steam boilers and the common faults and treatment methods of steam reciprocating pumps 1. Biomass boilers are a type of boiler. Boilers that use biomass energy as fuel are called biomass boilers. They are divided into biomass steam boilers, biomass hot water boilers, biomass hot air furnaces, biomass thermal oil furnaces, vertical biomass boilers, horizontal biomass boilers, etc. Oil-fired gas boilers refer to boilers that can burn both oil and gas. There was no such dual-fuel boiler before, because the burner was either oil or gas, and there was no dual-fuel burner. With the rapid development of thermal energy equipment in the world, some European countries began to produce and sell oil-fired gas burners. The organic combination of dual-fuel burners and boilers gave birth to a new type of boiler-oil-fired gas boilers. 1. The area close to the steam boiler room should be equipped with sufficient and effective fire-fighting equipment. 2. The steam boiler room must have staff on duty 24 hours a day, take turns to guard, and frequently check the water level line in the boiler to ensure that it is above the safety line to prevent explosions caused by dry combustion. If fire operations are carried out in flammable and explosive places, a fire operation permit must be obtained and adequate fire prevention measures must be taken before firefighting work can be carried out. In the event of a fire, a special person should be on duty at any time to observe the fire situation. 3. It is strictly forbidden to store containers containing flammable gases in the boiler room. 4. The staff of the steam boiler room must be certified before they can take up their posts, and they must be proficient in boiler operation technology and have a certain ability to discover and recognize safety hazards. 5. If boiler safety maintenance is carried out regularly in accordance with the boiler operating procedures, each unsafe standard should be carefully checked during the inspection process. 6. The distribution lines set in the steam boiler room should be protected by metal pipes or non-combustible hard plastic pipes, and the switch boxes should be installed outside the boiler room separately to achieve power outages, and unqualified safety devices are prohibited. 1. What is the reason why the steam reciprocating pump is not draining? How much, how? Answer: (1) Cause of failure: 1 The suction or discharge pipe is blocked. (2) The inlet and outlet valves are stuck. There is air in the cylinder. (4) The suction pipe is not connected tightly. (5) The plunger (piston) seal is seriously damaged. (2) Troubleshooting method: (1) Eliminate pipe blockage. (2) Remove the plugs on the inlet and outlet valves. (3) Fill with water and exhaust the air. (4) Tighten the pipe. (5) Replace the plunger (piston) seal.
Gas boiler burner failure and treatment method - the best gas boiler  1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. 2. The ignition rod is broken. Moisture. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation of the ignition rod is damaged and short-circuited to the ground. 5. Faults in the ignition cable and transformer: the cable is broken, the connector is damaged, causing a short circuit during ignition; the transformer is broken or other faults occur.
What are the common faults and treatment methods of gas boiler burners? , Gas boiler burner faults and treatment methods - the best gas boiler 1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. 2. The ignition rod is broken. Wet. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation sheath of the ignition rod is damaged and short-circuited to the ground. 5. Faults in the ignition cable and transformer: the cable is broken, the connector is damaged, causing a short circuit during ignition; the transformer is broken or other faults occur. There are five treatment measures: clear, replace, adjust the distance, change the line, and change the transformer. 2. The reason why the gas boiler ignition rod has sparks but cannot ignite: 1. The ventilation gap of the cyclone disk is blocked by carbon deposits and the ventilation is poor. 2. The oil nozzle is unclean, blocked or worn. 3. The air door setting angle is too small. 4. The distance between the tip of the ignition rod and the front edge of the oil nozzle is inappropriate (too protruding or retracted) 5. The first oil gun solenoid valve is blocked by debris (small fire oil gun). 6. The oil is too viscous and difficult to flow or the filter system is blocked or the oil valve is not open, so that the oil pump does not absorb enough oil and the oil pressure is low. 7. The filter of the oil pump itself is blocked. 8. The oil contains a lot of water (boiling noise in the heater). The treatment measures are: clear; clean first, if it doesn’t work, replace it with a new one; adjust the distance (3~4mm is better); remove and clean (clean the parts with diesel); check the pipeline and oil filter, insulation equipment; remove the outer screws of the oil pump, carefully remove the outer cover and take out the oil net inside, soak it with diesel; try it with new oil.
Gas boiler burner failure and treatment method-the best gas boiler 1. Reasons why the ignition rod of the gas boiler burner does not ignite: 1. There is carbon slag and oil stains in the gap between the ignition rods. What are the common failures and treatment methods of gas boiler burners? . 2. The ignition rod is broken. Damp. Leakage. 3. The distance between the ignition rods is incorrect, too long or short. 4. The insulation outer skin of the ignition rod is damaged, short-circuited to the ground. 5. Faults in the ignition cable and transformer: cable breakage, connector damage, short circuit during ignition; transformer breakage or other faults. There are five treatment measures: cleaning, replacement, distance adjustment, line change, transformer change. 2. The reason why the gas boiler ignition rod has sparks but cannot ignite: 1. The ventilation gap of the cyclone disk is blocked by carbon deposits and poor ventilation. 2. The oil nozzle is unclean, blocked or worn. 3. The air door setting angle is too small. 4. The distance between the tip of the ignition rod and the front edge of the oil nozzle is inappropriate (too protruding or retracted) 5. The first oil gun solenoid valve is blocked by debris (small fire oil gun). 6. The oil is too viscous and difficult to flow or the filtration system is blocked or the oil valve is not opened, so that the oil pump does not absorb enough oil and the oil pressure is low. 7. The filter of the oil pump itself is blocked. 8. The oil contains more water (boiling noise in the heater). The treatment measures are: clear; clean first, if it doesn't work, replace with a new one; adjust the oil for testing; adjust the distance (3~4mm is better); remove and clean (clean the parts with diesel); check the pipeline and oil filter, insulation equipment; remove the screws outside the oil pump, carefully remove the outer cover and take out the oil net inside, soak it with diesel; try with new oil. 3. When the gas boiler is normal at a low fire and turns to a high fire, it goes out or flickers unsteadily. Reasons: 1. The air volume of the damper of the high fire is set too large. 2. The micro switch of the oil valve of the high fire (the outermost group of the damper) is not set properly (the setting is larger than the air volume of the damper of the high fire). 3. The viscosity of the oil is too high and it is not easy to atomize (heavy oil). 4. The distance between the cyclone disk and the oil nozzle is improper. 5. The oil nozzle of the high fire is worn or dirty. 6. The heating temperature of the reserve oil tank is too high, causing the steam to make the oil pump deliver oil smoothly. 7. The oil in the oil boiler contains water. Treatment measures: gradually reduce the test; increase the heating temperature; adjust the distance (between 0~10mm); clean or replace; set it to about 50℃; change the oil or drain. 4. Reasons for the increase in noise of the gas boiler burner: 1. The stop valve in the oil circuit is closed or the oil inlet is insufficient, and the oil filter is blocked. 2. The oil inlet temperature is low, the viscosity is too high or the pump oil inlet temperature is too high. 3. The oil pump is faulty. 4. The fan motor bearing is damaged. 5. The fan impeller is too dirty. Treatment method: ① Check whether the valve in the oil pipeline is open, whether the oil filter is working properly, and clean the filter of the pump itself. ② Heat the oil or lower the oil temperature. ③ Replace the oil pump. ④ Replace the motor or bearing. ⑤ Clean the fan impeller.