There are generally two types of filters, oil filters and air filters. The editor wants to talk to you about the application of oil filters.
Oil filters are important filtering devices in thermal oil systems and are very important for the operating safety of oil transportation systems. However, in fact, it is found that many companies have not paid enough attention to the setting of filters. They are either not set up or not set up reasonably. Once problems arise, they cannot be avoided and cause direct losses.
Filters, as the name suggests, are filtering facilities. Their main function is to filter out the colloids produced during the operation of thermal oil. But what is the reality? Although many companies have also set up filters, the filters are either too small or set up unreasonably. Thermal oil cannot be precipitated during high-temperature and high-speed operation, let alone filtered. What is even more bizarre is that the filter is not set at the lower part of the entire system, but on the vertical pipe. Imagine, can such a device filter out the colloid? No. We know that heat transfer oil cannot settle at high temperature, which requires a forced filtration process. Under normal circumstances, if the 80-mesh filter is not completely blocked, it will not pose a threat to the heat transfer oil pipeline and equipment, but the scene we saw on site is shocking. Some units only think of cleaning once every seven or eight years, which can not but be said to be the factory's negligence.
Filter When glue is used to block the lower part of the pipeline and equipment, the heating capacity of the system can be seen. Therefore, even if the filter is installed, it cannot be taken lightly. It needs to be kept in a normal state so that the filter can be repaired and cleaned correctly. If the production is tight, it can be cleaned through the bypass line, and the production can continue to work. In short, the role of the filter in the heat transfer oil system cannot be ignored. Its appropriate setting should be set at the front end of the heat transfer oil pump to avoid other impurities in the system from entering the pump body and damaging the oil pump impeller. At the same time, the height and diameter of the filter should be increased as much as possible. The larger the volume, the greater the filtration capacity, but this is relative. The unreasonable setting will not play a filtering role. Therefore, the inlet and outlet of the filter should have uniform diameters and be free to enter and exit. The pipeline should be cleaned frequently.
In addition, the valve device should be installed on both sides of the filter, otherwise the operation cannot be controlled and executed. The valve is an effective control means, and the temperature should be selected according to the selected temperature. Generally speaking, it is better to control the two devices of the oil pump and the filter with three valves. Less setting and no setting will not be able to control when encountering problems.
Filter price The oil filter belongs to the pipeline coarse filter, which can be used for filtering large particles of liquid, gas or other media. It can be installed on the pipeline to remove larger solid impurities in the fluid, so that the machine equipment (including compressors, pumps, etc.) and instruments can work and operate normally, achieve the function of stabilizing the process and ensuring reliable production. When the fluid enters the filter cartridge with a certain size of filter, its impurities are blocked, and the clean filtrate is discharged from the filter outlet. When cleaning is required, take out the removable filter element and reinstall it after processing. Therefore, it is very convenient to use and maintain.
1. The oil filter can be installed horizontally or vertically, and the inlet and outlet directions should be consistent with the arrow direction on the valve body.
2. After the filter has been working for a period of time, a certain amount of impurities are precipitated in the filter element. At this time, the pressure drop increases and the flow rate decreases. The impurities in the filter element need to be cleaned in time.
3. When cleaning impurities, pay special attention to the stainless steel wire mesh on the filter element. It cannot be deformed or damaged. Otherwise, the filter will be installed again. The purity of the filter medium does not meet the design requirements, and the compressor, pump, instrument and other equipment will be damaged. 4. If the stainless steel wire mesh is found to be deformed or damaged, it needs to be replaced immediately.
There are generally two types of filters, oil filters and air filters. The editor wants to talk to you about the application of oil filters.
Oil filters are important filtering devices in thermal oil systems and are very important for the operating safety of oil transportation systems. However, in fact, it is found that many companies have not paid enough attention to the setting of filters. They are either not set up or not set up reasonably. Once problems arise, they cannot be avoided and cause direct losses.
Filters, as the name suggests, are filtering facilities. Their main function is to filter out the colloids produced during the operation of thermal oil. But what is the reality? Although many companies have also set up filters, the filters are either too small or set up unreasonably. Thermal oil cannot be precipitated during high-temperature and high-speed operation, let alone filtered. What is even more bizarre is that the filter is not set at the lower part of the entire system, but on the vertical pipe. Imagine, can such a device filter out the colloid? No. We know that heat transfer oil cannot settle at high temperature, which requires a forced filtration process. Under normal circumstances, if the 80-mesh filter is not completely blocked, it will not pose a threat to the heat transfer oil pipeline and equipment, but the scene we saw on site is shocking. Some units only think of cleaning once every seven or eight years, which can not but be said to be the factory's negligence.
Filter When glue is used to block the lower part of the pipeline and equipment, the heating capacity of the system can be seen. Therefore, even if the filter is installed, it cannot be taken lightly. It needs to be kept in a normal state so that the filter can be repaired and cleaned correctly. If the production is tight, it can be cleaned through the bypass line, and the production can continue to work. In short, the role of the filter in the heat transfer oil system cannot be ignored. Its appropriate setting should be set at the front end of the heat transfer oil pump to avoid other impurities in the system from entering the pump body and damaging the oil pump impeller. At the same time, the height and diameter of the filter should be increased as much as possible. The larger the volume, the greater the filtration capacity, but this is relative. The unreasonable setting will not play a filtering role. Therefore, the inlet and outlet of the filter should have uniform diameters and be free to enter and exit. The pipeline should be cleaned frequently.
In addition, the valve device should be installed on both sides of the filter, otherwise the operation cannot be controlled and executed. The valve is an effective control means, and the temperature should be selected according to the selected temperature. Generally speaking, it is better to control the two devices of the oil pump and the filter with three valves. Less setting and no setting will not be able to control when encountering problems.
Filter price The oil filter belongs to the pipeline coarse filter, which can be used for filtering large particles of liquid, gas or other media. It can be installed on the pipeline to remove larger solid impurities in the fluid, so that the machine equipment (including compressors, pumps, etc.) and instruments can work and operate normally, achieve the function of stabilizing the process and ensuring reliable production. When the fluid enters the filter cartridge with a certain size of filter, its impurities are blocked, and the clean filtrate is discharged from the filter outlet. When cleaning is required, take out the removable filter element and reinstall it after processing. Therefore, it is very convenient to use and maintain.
1. The oil filter can be installed horizontally or vertically, and the inlet and outlet directions should be consistent with the arrow direction on the valve body.
2. After the filter has been working for a period of time, a certain amount of impurities are precipitated in the filter element. At this time, the pressure drop increases and the flow rate decreases. The impurities in the filter element need to be cleaned in time.
3. When cleaning impurities, pay special attention to the stainless steel wire mesh on the filter element. It cannot be deformed or damaged. Otherwise, the filter will be installed again. The purity of the filter medium does not meet the design requirements, and the compressor, pump, instrument and other equipment will be damaged. 4. If the stainless steel wire mesh is found to be deformed or damaged, it needs to be replaced immediately.