Generally, when we use the hot blast stove, the hot blast stove will be formed after long-term use, and the furnace mouth will be damaged. How should we deal with it at this time. This kind of hot air stove uses the method of direct combustion of fuel, and forms hot air after high purification treatment, and then directly contacts with materials to heat, dry or bake. It is such a kind of equipment, which became the replacement product of electric heat source and traditional steam power heat source at that time. Hot air stove is not a boiler? What's the difference? Only by using hot air as the medium and carrier of the hot blast stove can the heat utilization rate and thermal work effect be greatly improved. It is classified as an industrial product and belongs to a type of boiler, but in terms of the definition of special equipment, hot blast stoves are not within the scope of special equipment boilers. The hot blast stove is a new type of shell and tube high temperature heat energy recovery.
Analysis of the air volume calculation method of the hot blast stove Under certain heat exchange and temperature conditions, the temperature of the heat exchange wall surface can be as high as 600~700°C. If the air cooling conditions on the part of the surface are not good, the wall temperature may also rise. Under the same heat load, hot blast stoves require more heat transfer area than ordinary steam boilers or hot water boilers. The following is an understanding of the air volume calculation of hot blast stoves.
What factors affect the performance of the hot blast stove? Energy needs to be used when the hot blast stove is used. It is precisely because of this that it is necessary to pay attention to the energy-saving performance of the product. When a product is not energy-saving when it is used, it is natural It will increase its use cost. It is precisely because the energy saving of this product is affected by many factors.
Generally, when we use the hot blast stove, the hot blast stove will be formed after long-term use, and the furnace mouth will be damaged. How should we deal with it at this time. This kind of hot air stove uses the method of direct combustion of fuel, and forms hot air after high purification treatment, and then directly contacts with materials to heat, dry or bake. It is such a kind of equipment, which became the replacement product of electric heat source and traditional steam power heat source at that time. However, due to long-term use, the contact surface between the middle sleeve and the small sleeve of the tuyere of the hot blast stove will be wet, seepage or foam, and there will be yellow gas flames around the tuyere.
After further inspection, we found that there are air bubbles in the outlet head of the hot blast stove, and there are white lines in the water flow. If it is serious, the water outlet will be intermittent and the water temperature difference will increase. When the air outlet leaks too much, there will be water seepage in all three sets, and water seepage will also occur when it reaches the edge of the air outlet. Performances like these can fully prove that the hot blast stove has burnout at the furnace mouth.
Generally, when we use the hot blast stove, the hot blast stove will be formed after long-term use, and the furnace mouth will be damaged. How should we deal with it at this time. This kind of hot air stove uses the method of direct combustion of fuel, and forms hot air after high purification treatment, and then directly contacts with materials to heat, dry or bake. It is such a kind of equipment, which became the replacement product of electric heat source and traditional steam power heat source at that time. Hot air stove is not a boiler? What's the difference? Only by using hot air as the medium and carrier of the hot blast stove can the heat utilization rate and thermal work effect be greatly improved. It is classified as an industrial product and belongs to a type of boiler, but in terms of the definition of special equipment, hot blast stoves are not within the scope of special equipment boilers. The hot blast stove is a new type of shell and tube high temperature heat energy recovery.
Analysis of the air volume calculation method of the hot blast stove Under certain heat exchange and temperature conditions, the temperature of the heat exchange wall surface can be as high as 600~700°C. If the air cooling conditions on the part of the surface are not good, the wall temperature may also rise. Under the same heat load, hot blast stoves require more heat transfer area than ordinary steam boilers or hot water boilers. The following is an understanding of the air volume calculation of hot blast stoves.
What factors affect the performance of the hot blast stove? Energy needs to be used when the hot blast stove is used. It is precisely because of this that it is necessary to pay attention to the energy-saving performance of the product. When a product is not energy-saving when it is used, it is natural It will increase its use cost. It is precisely because the energy saving of this product is affected by many factors.
Generally, when we use the hot blast stove, the hot blast stove will be formed after long-term use, and the furnace mouth will be damaged. How should we deal with it at this time. This kind of hot air stove uses the method of direct combustion of fuel, and forms hot air after high purification treatment, and then directly contacts with materials to heat, dry or bake. It is such a kind of equipment, which became the replacement product of electric heat source and traditional steam power heat source at that time. However, due to long-term use, the contact surface between the middle sleeve and the small sleeve of the tuyere of the hot blast stove will be wet, seepage or foam, and there will be yellow gas flames around the tuyere.
After further inspection, we found that there are air bubbles in the outlet head of the hot blast stove, and there are white lines in the water flow. If it is serious, the water outlet will be intermittent and the water temperature difference will increase. When the air outlet leaks too much, there will be water seepage in all three sets, and water seepage will also occur when it reaches the edge of the air outlet. Performances like these can fully prove that the hot blast stove has burnout at the furnace mouth.