The special-shaped burner adopts low-carbon, environmentally friendly and clean new energy, which can replace traditional energy products such as petrochemical diesel, liquefied petroleum gas, and coal. It can be widely used in hotels, factories, schools and families as non-power fuel. Applied to various heat energy equipment, such as road construction asphalt heating heat conduction furnace, food oven, air conditioner heater, snow sweeper, incinerator, hot air generator and so on.
Its main features are mature technology, high degree of refinement, and good quality (high security and stable system). Electric spark ignition is used to realize automatic control. The combustion state is dynamically monitored. Once the flame detector detects the flameout signal, it will be fed back to the burner within a short period of time, and then it will enter the protection state and cut off the gas supply at the same time. The flame detector should be able to sense the flame signal normally, neither sensitive nor dull. It is generally required that the response time from the flameout to the flame detector sending out the flameout signal should not exceed 0.2 seconds. When the special-shaped burner is ignited, gas is passed in, and the gas ignites and burns. The ignition action is required to occur before the gas is introduced, and the ignition temperature field is formed first, which is convenient for ignition and combustion.
Environmental leakage of gas pressure regulating equipment may cause personnel poisoning, so work site accidents must be highly valued. First ensure that the pipeline is sealed, and regularly check the pipeline for leaks. If the pipeline leaks, it must be eliminated before continuing to use; secondly, to avoid poisoning and high gas concentration, the work site is required to be well ventilated: equipped with ventilation holes and ventilation devices; in addition , require the work site to prohibit fireworks and electrical parts. Smoking, welding, cutting and other illegal operations at the work site are strictly prohibited.
For the operation of the entire equipment, the operator should refer to the furnace safety operation regulations and good process requirements for operation.
In the process of debugging, be careful. When adjusting, the pressure display is critical. Turn the low air pressure and high air pressure switches to verify they are working. The connection of the air valve needs to be cleaned and repaired. If the connection is sticky or too rough, it needs to be replaced with a suitable fitting. If detachable pipelines are installed, care should also be taken to clean them. Determine whether the exhaust damper is working normally, whether the operation of the special-shaped burner and some requirements in the processing process, and whether the settings are correct. Check the connection of the damper to see if it works. Check the damper blades for wear. Check to see if the barometer is working properly.
The special-shaped burner adopts low-carbon, environmentally friendly and clean new energy, which can replace traditional energy products such as petrochemical diesel, liquefied petroleum gas, and coal. It can be widely used in hotels, factories, schools and families as non-power fuel. Applied to various heat energy equipment, such as road construction asphalt heating heat conduction furnace, food oven, air conditioner heater, snow sweeper, incinerator, hot air generator and so on.
Its main features are mature technology, high degree of refinement, and good quality (high security and stable system). Electric spark ignition is used to realize automatic control. The combustion state is dynamically monitored. Once the flame detector detects the flameout signal, it will be fed back to the burner within a short period of time, and then it will enter the protection state and cut off the gas supply at the same time. The flame detector should be able to sense the flame signal normally, neither sensitive nor dull. It is generally required that the response time from the flameout to the flame detector sending out the flameout signal should not exceed 0.2 seconds. When the special-shaped burner is ignited, gas is passed in, and the gas ignites and burns. The ignition action is required to occur before the gas is introduced, and the ignition temperature field is formed first, which is convenient for ignition and combustion.
Environmental leakage of gas pressure regulating equipment may cause personnel poisoning, so work site accidents must be highly valued. First ensure that the pipeline is sealed, and regularly check the pipeline for leaks. If the pipeline leaks, it must be eliminated before continuing to use; secondly, to avoid poisoning and high gas concentration, the work site is required to be well ventilated: equipped with ventilation holes and ventilation devices; in addition , require the work site to prohibit fireworks and electrical parts. Smoking, welding, cutting and other illegal operations at the work site are strictly prohibited.
For the operation of the entire equipment, the operator should refer to the furnace safety operation regulations and good process requirements for operation.
In the process of debugging, be careful. When adjusting, the pressure display is critical. Turn the low air pressure and high air pressure switches to verify they are working. The connection of the air valve needs to be cleaned and repaired. If the connection is sticky or too rough, it needs to be replaced with a suitable fitting. If detachable pipelines are installed, care should also be taken to clean them. Determine whether the exhaust damper is working normally, whether the operation of the special-shaped burner and some requirements in the processing process, and whether the settings are correct. Check the connection of the damper to see if it works. Check the damper blades for wear. Check to see if the barometer is working properly.